The 10 Commandments of Email Thou shalt include a clear and specific subject line. Thou shalt edit any quoted text down to the minimum thou needest. Thou shalt...
22559
Ralph DeBlasi
rsdcpa@...
Oct 1, 2000 10:26 am
Can anybody help me with the following problem. A short has developed in my track buss that I cannot track down. Any tips would be helpfull. The problem is...
22560
Frank A. Rosenbaum
farosenbaum@...
Oct 1, 2000 10:36 am
Is this short on new or old track? If it is old track, has an insulated gap closed up? Were you doing track work recently? Check for spikes or other free...
22561
Manhart Matthias
matthias.manhart@...
Oct 1, 2000 10:39 am
Hallo Gordon, i use the LGB 55025 switch decoder with my Digitrax Chief. The programming is a little bit special. You can find some help on my homepage ...
22562
Larry Mort
RevMort@...
Oct 1, 2000 11:10 am
... Another question. Other than the jumper on the front of the booster to set t up as a booster, are there any other things I shold check to make sure I ...
22563
Brian Brandt
trains@...
Oct 1, 2000 1:14 pm
I have a question , can we use the loconet cableing to use a booster at a remote part of the layout? We have our main boosters at a control area, but the...
22564
Ben Young
bly801680@...
Oct 1, 2000 1:57 pm
Do you have, or is this a reverse loop(section) on your layout? If it is, you will need a method of handling reversing sections such as a second reversing...
22565
Bruce Petrarca
Bruce@...
Oct 1, 2000 3:40 pm
Hello everyone - I was operating an analog loco LifeLike P2K E7A with a DB-150, using address 00. I shut down the loco - turned the throttle to 00. As it was...
22566
mgruber803@...
Oct 1, 2000 7:55 pm
I plan to install a DG 580 decoder in An LGB mogul. I would appreciate any advice on how to dissemble the loco. Thanks in advance Sincerely, Mike...
22567
greg.moore@...
Oct 1, 2000 7:59 pm
Brian As long as you have a good common ground between the 2 boosters this will not be a problem. Cheers Greg Auckland, NZ...
22568
Mike Curtis
macurtis@...
Oct 2, 2000 1:56 am
Sorry about leaving the chat so abruptly! My ISP is having problems. Cable connections are supposed to be better than this! -- Mike Curtis, Deputy Chief Salem...
22569
Chris Shinn
cnshinn@...
Oct 2, 2000 2:02 am
No Problem, Mike. Try again later. I have cable, too. Less problems, but when they go down...they go down! Chris... ... From: "Mike Curtis"...
22570
John Burkhardt
burkhj@...
Oct 2, 2000 7:20 am
Andrew, IMHO, the list needs such light hearted interludes from time to time. I for one had a good laugh for a good while - in fact it made my day! By all...
22571
Harold G. Jones
hgjones@...
Oct 2, 2000 12:13 pm
Don, Dennis & Peter: If you feel there is no problem then why does one have to use a password to access. All sites requiring a password should be secure....
22572
Harold G. Jones
hgjones@...
Oct 2, 2000 12:16 pm
Larry: The DB100a that came with the Big Boy system has a switch position for auto-reverse and the Chief's DCS100 has a Option switch which you set with your ...
22573
jean piquette
piquettejc@...
Oct 2, 2000 12:46 pm
Hi everyone, I just zeroed in on a problem that's been driving me buggy for months. Don't have any idea what's causing it. Any comments would be appreciated. I...
22574
Ross Kudlick
r_kudlick@...
Oct 2, 2000 1:04 pm
The type (and cost) of the security technology used in any given situation should be commensurate with the security needs. When sensitive, critical or ...
22575
tractionfan@...
Oct 2, 2000 2:54 pm
If anyone is planning to be in the Altoona, PA area this weekend (NMRA/MER regional convention and the Altoona RR Museum's RailFest) come see my three HO...
22576
Stefano
auro@...
Oct 2, 2000 5:35 pm
Hi, as railfan and as governator (vice-president) of TMRC (Tech Model Railroad Club of MIT) I am "trying" to setup something as a "MIT Railroad Association",...
22577
Denny Anspach
danspach@...
Oct 2, 2000 7:25 pm
If anyone on this list has successfully installed a decoder in a Fleishmann ICE locomotive, would you kindly contact me off-list? Thank you. Denny Denny S....
22578
bernhard@...
Oct 2, 2000 9:19 pm
Are you shure they are 1.5 volt bulbs? I don't have an SD9 but found the same problem on several of their other models and suspect the bulbs were 3volts. For...
22579
steitzj@...
Oct 2, 2000 10:00 pm
Listnauts: My old DB150 was a casualty at a train show recently, but the good news is that my hosts at the train show more than made up for my loss with a new...
22580
Jon Miller
atsf@...
Oct 2, 2000 10:10 pm
The DB150 is the newer replacement for the older DB100a. The DB150 is rated at 5 Amp 80 Watts and the DB100a was rated at 4.5 Amp 80VA. One of the main...
22581
Tim Broadley
tbroadley@...
Oct 2, 2000 10:44 pm
Greetings all: I'm a newcomer to this group and Digitrax. I pretty much understand how it works etc. I am in the process of equipping some of my engines with...
22582
John M. Wallis
jwallis@...
Oct 2, 2000 10:47 pm
Hi John: The DB100a is the booster originally supplied with the BigBoy set. It is a pure 5A auto-reversing power booster and required the DT200 throttle as a ...
22583
John Deecker
jdeecker@...
Oct 2, 2000 10:53 pm
The DB100xx is the booster that was used with the Big Boy system and was also sold as a standalone booster in several versions. It is however not a command...
22584
steitzj@...
Oct 2, 2000 11:11 pm
... Folks, Sorry I've been out of the loop on this, but with back-to-school at work, an apartment move, and a lot of other things, my model railroading has...
22585
Jeff Warner
jwarner@...
Oct 2, 2000 11:45 pm
... I used a Lenz LE103XF (thinner than a DH121) and set it inside the boiler just under the smoke stacks. Make sure you put a peice of electrical tape or two...
22586
Denny Anspach
danspach@...
Oct 2, 2000 11:47 pm
It has become more and more common for Digitrax decoders (and others) to simply be lumped into standard types that will handle "all standard HO can motors"...
22587
Bill Roger
billroger@...
Oct 3, 2000 12:32 am
Denny: What is the price of that little beauty (#20338-9)? What decoder would you recommend? Bill ... From: "Denny Anspach" <danspach@...> To:...
