My computer was infected by a virus yesterday. I caused an email to be sent to most if not all of my address book. The email was sent late Sat or early Sun....
David: WOW, thanks for the heads up. I will not be recommending Juno in the future without mentioning this aspect! This takeover/invasion of my property was...
Sounds like you have a third type which is neither piston nor wedge...the piston type has a piston in the middle of the dovetail which pokes straight out to...
... If the hole for the drive rivets goes all the way through the casting, you may be able to drive them out from the back. Failing that I have had luck using...
Mike, I would be interested to get this manual too. Could you send it under : j.c.gerber@... Thank you Regards Jean-Claude, Switzerland ...
14441
LouD31M066@...
Dec 2, 2001 7:05 am
My experience with bed frames is they are thin gage and heat treated hard. Difficult to drill even with a cobalt drill. Regular angle iron is meaty and soft...
14440
Herman
papadoo@...
Dec 2, 2001 6:15 am
... you are a man after my heart. . . . I *dumpster-dive* around apartment buildings for discarded bed frames. The angle iron is great for making machine...
after searching thru the archives without luck I found lots of additional info in this group by going to: http://members.home.net/escarcega/metal.htm (given on...
... I would think that would get you a pulley for an AA lathe, not the Atlas 618... david David Beierl - Providence, RI USA 6 (or 3)" Atlas lathe ca. 1941...
thanx for the info. I did manage to find some more out myself by going to http://members.home.net/escarcega/metal.htm then RCM drop box and then to retired...
Well, I did all my work on an old Logan, so I can relate. Are you on the Logan lathe-list group? lathe-list@yahoogroups.com In fact, I roughed it and used a...
Thanks, Jerry. Both the owner of the 109 and I have access to a full machine shop, they are going to try to straighten the spindle, if not, they'll make a new...
... Worldnet.att.com has been highly rated by users. I'm quite satisfied with attglobal.net, but they are certainly not the cheapest solution. My serious...
14433
Bob May
bobmay@...
Dec 1, 2001 11:11 pm
I use one of the freespace website places -FortuneCity for my webspace. It does have the problem of being a redirection type setup (the base page refers to...
14432
John Johnson
jjohnson@...
Dec 1, 2001 10:43 pm
Louis, Don't be afraid to turn cast iron on your lathe. I have turned all twelve of my Shay steam locomotive wheels which are cast iron, on my 12x36 Craftsman...
I am using Juno, and am satisfied. They have hundreds of local access numbers (I have about 10 local numbers available to me right here in rural NH!). Quite...
I've never found that there is any problem with a skin on cast iron. Cast iron is quite soft and easy to machine. It is very abrasive and does eat up tool...
Tough skin and impurities on cast parts surfaces, yes, but it isn't all like that. I've bought several REMs of cast iron from the local tool steel distributor...
14426
LouD31M066@...
Dec 1, 2001 8:53 pm
I have shyed away from trying to work with cast iron because I've read that castings have a hard shell, impurities like sand and very hard spots due to rapid ...
I've needed backing plates for several of the lathes I've owned. I've found that the easiest place to get the basic blank is to go to a thrift store or...
... Could someone 'splain the difference between these? I have a Harbor Freight toolpost which has female dovetails on two adjacent sides, each having a...
14423
michaelhenry@...
Dec 1, 2001 6:32 pm
... how it ... This might be a good time to mention that those of us (like me) that read the group on the web have no easy way to directly get a member's email...
14422
Ben Bennett
greyhawk200@...
Dec 1, 2001 2:51 pm
My ISP just announced that they were going to double my rate so since I'm basicily a cheapskate and I'm not real happy with them anyway I've decided to change....
... Kevin; I made my 8" faceplate from a rough cast 8" backplate. These backplates are available from the mail order places. I make backplates from these too...
... Frank; There has been good reviews of these toolposts by members of this group in the past. The only problem found with them is that you should replace...
... Take the chucks with you to a good hardware store. They should carry replacement keys, and you can try them out on the chucks there. Ron Thibault ...
