Bought an Atlas 10-326 steady rest without blades/fingers. I need to find out what size the fingers are so I can order square brass stock to fabricate new...
65711
david sacco
worldcup947222
Oct 1, 2010 4:13 pm
Cool, so I'm putting that chrome handle in the freezer before trying to press the cam metal (might not be zamak) through the handle. Thanks Dave ...
65712
Lee Miller
lee.hlfs
Oct 1, 2010 4:23 pm
They are 3/8" square stock. _____ From: atlas_craftsman@yahoogroups.com [mailto:atlas_craftsman@yahoogroups.com] On Behalf Of vollrathdc Sent: Friday, October...
65713
carvel webb
cwlathes
Oct 1, 2010 7:37 pm
3/8" square phosphor bronze if you can find some , Regards, Carvel ... From: atlas_craftsman@yahoogroups.com [mailto:atlas_craftsman@yahoogroups.com] On Behalf...
65714
Keith Mc
acti42
Oct 1, 2010 8:56 pm
Well, which is cheaper, the Change Gear Set, or a used QCGB from [where?]? Honestly, I don't think I really need a QCGB. This is hobby use, not "production". ...
65715
Scott Henion
shdesigns2003
Oct 1, 2010 9:03 pm
... I have seen sets of gears go on ebay for less then $50 (usually $60-70.). Individual gears $8 The cheapest QCGB I have seen was over $200. You also need...
65716
carvel webb
cwlathes
Oct 2, 2010 6:05 pm
Hi Keith , Keep a look out on Ebay - but note that the QCGB for the 10" and 12" are not the same - you will also need the rest of the gear train and tumbler...
65717
carvel webb
cwlathes
Oct 2, 2010 8:59 pm
Have a look at http://www.lathes.co.uk/atlas/ The first picture on the page has a "V" vertical countershaft assembly , the second picture has an "H" horizontal...
65718
harpanet13
Oct 3, 2010 3:57 am
This months "Home Shop Machinist" magazine has an article on restoring an old metal lathe as its cover story. Interesting article. Great magazine overall. ...
65719
Bill Stietenroth
k5zty
Oct 3, 2010 10:02 am
Get your parts diagram out and make sure you have all the correct parts in the correct order from top to bottom. It is a self centering lock wedge and should...
65720
mertnedp
Oct 3, 2010 3:22 pm
A friend has the above for sale. There are 2 Atlas lathes for sale in the Niagara Falls area. Mike is asking $800 each with some tooling. There are too many...
65721
Wilfred Hoafat
whoafat
Oct 3, 2010 3:40 pm
Keith, I have watched this thread hopping that you will find the gears. The QCGB sometimes sells for as much as the lathe itself. If you should run out of ...
65722
Bill Stietenroth
k5zty
Oct 3, 2010 5:00 pm
This reply was sent to the list on Sept. 25th. Not very timely. Bill ... From: "Bill Stietenroth" <k5zty@...> To: atlas_craftsman@yahoogroups.com Subject:...
65723
harpanet13
Oct 3, 2010 7:39 pm
Does anyone know if this lower swivel will fit the earlier 10' one piece carriage, (the one with the Zamak section in the compound) ? ...
65724
mertnedp
Oct 3, 2010 11:18 pm
I have an early 1 piece carriage and it has this mounted on it. But my question is what zamak piece are you talking about?...
65725
harpanet13
Oct 3, 2010 11:38 pm
It is labeled as the lower swivel on the drawings I have of the 10-F. You can see mine in the lower right of the first picture in album "Waynes World". Instead...
65726
mertnedp
Oct 4, 2010 1:25 am
Interesting I wonder when it was changed to all iron as mine is. I have both carriages as I converted to power cross feed a few years ago....
65727
Conrad Falk
conrade333
Oct 4, 2010 12:35 pm
any one have a dead ceter for the 109 for sale. It is a o If so contact conradfalk @ yahoo.com [Non-text portions of this message have been removed]...
65728
Scott Henion
shdesigns2003
Oct 4, 2010 1:12 pm
... http://www.homeshopsupply.com/parts.html Look for par #A-235. -- ... Scott G. Henion Craftsman 12x36 lathe: http://shdesigns.org/Craftsman12x36...
65729
Mike Nicewonger
twmaster...
Oct 6, 2010 3:38 am
Hi gang, I've got a milling attachment for the 10-12 inch lathes for sale. I don't have an Atlas that big. I have no use for this. Atlas part 10-501. This is a...
65730
joe
joe48234
Oct 6, 2010 4:14 am
I just bought one off of ebay. Wish you sold it earlier.  Do you have a atlas_craftsman  taper attachment for 10 -12 lathe for sale?  Thanks Bruno ......
65731
Mike Nicewonger
twmaster...
Oct 6, 2010 4:20 am
... Just got it this weekend. ... No other stuff for the 10-12" lathes. Just this one part. Please direct any inquiries to me OFF LIST. -- Mike N "That's one...
65732
joe
joe48234
Oct 6, 2010 5:13 am
I am looking for Atlas Craftsman taper attachment 10" - 12" lathe. I checked ebay and they are too much money. Thanks Bruno My email :joe48234@... ...
65733
metal2
bigmetalpaul
Oct 6, 2010 7:13 am
I have a bandsaw brazer what its called I am looking for any information please. information I got off it the electro band saw brazer made by nelson &...
65734
Jt Email
jtrcy
Oct 6, 2010 12:53 pm
Check Harbor Freight or Grizzly or Jet for PDF manuals of their versions. I've got an older Jet bandsaw blade welder and with a bit of practice, I've been able...
65735
Steve
skadsm@...
Oct 6, 2010 3:02 pm
... checked >ebay and they are too much money. Check metalworking websites and you can find various plans to make one. Probably the only way you are going to...
65736
James Irwin
jimirwin2001
Oct 6, 2010 3:34 pm
My issue with taper attachments, is they are too short. I suppose this is to improve stiffness. So I may someday make a double length bar for mine for my 12x36...
65737
David Vollrath
vollrathdc
Oct 6, 2010 4:54 pm
A couple of weeks ago someone asked for a drawing of some parts for the Atlas 760 taper attachment. Since the Taper Attachment topic has come up again and ...
65738
Jon Elson
jmelson2
Oct 6, 2010 5:04 pm
... Are you sure it is a "brazer"? Typically, these are called welders, and weld the blade with no filler or brazing material added. I have an ancient German...
65739
metal2
bigmetalpaul
Oct 6, 2010 5:26 pm
yes its a brazer has 2 carbon on it when you push them together it like restince welding i think mcmaster carr used to sell it like 15 years ago but i lost...
