Jeff, The MS9307C+ (USB) does not have onboard video. It has been my experience that boards with onboard LAN and video can be kind of QUIRKY due to the shared...
706
Art
artfenerty
Aug 30, 2003 12:01 am
Hi Rab: Is on my list for next release.... Sorry for the delay, I thought it was working... Thanks, Art www.artofcnc.ca...
707
Art
artfenerty
Aug 30, 2003 12:13 am
... Sounds doable. ... Very hard to do in current code base. I'll give it some thought. Souns like what is needed is a G30 Wizard to do the digitizing of a...
708
csgchum
Aug 30, 2003 1:48 am
Just downloaded trial version of mach2 release one If I export a dfx file from corel 9 and convert it to g code nothing visual shows in tool path, only a red...
709
woody45130
Aug 30, 2003 1:48 am
Hi, Art said to ask questions here. Ok, I am looking for a schematic that uses the PWM signal from Mach2 to control the spindle RPM. Anybody? Thanks....
710
Servo Wizard
servowizard
Aug 30, 2003 2:04 am
Hi, The PWM spindle speed circuit consist of (1) 1k Ohm resistor (10k Ohm) and (1) 200 MFD capacitor (20MFD). The values in parentheses can be substituted with...
711
deruida
Aug 30, 2003 2:56 am
Hello all, I have been searching the archives for info on the spindle speed sensor and checked the files folder without any luck. Hopefully I didn't miss it, I...
712
Servo Wizard
servowizard
Aug 30, 2003 3:22 am
Dan, These are the two photoelectric sensors that Art recommended. EE-SY671 or EE-SY672. Servo...
713
Michael Milligan
zen11777
Aug 30, 2003 8:51 am
Art Many years ago we developed a general digitising package for use on machine tools, this package was able to capture data from both 3D and 2D unknown forms....
714
Steve Blackmore
stevepilotltd
Aug 30, 2003 12:32 pm
... Any news on "TURN" ? Is there only me having problems with speed control, or is there only me trying it? -- Steve Blackmore...
716
Art
artfenerty
Aug 30, 2003 1:41 pm
Steve: There a ew trying it, but I suspect your the only true step/dir spindle using it. I am busy with a couple of other things at the moment, I will be...
718
Mika Salmi
mstcnc
Aug 30, 2003 1:56 pm
Hi, to all I just tested pair of new encoders I got cheaply. The encoders are made in Taiwan by Hontko Co. Type is: HTR-HB-8-1024-3-L. Spec says they are 5V,...
722
gittt2000
Aug 30, 2003 4:11 pm
... pulse is only 3,3V which maybe is too low for my Rutex drives. ... Mika - you really need a 26C31 line receiver chip or similar. This will take the...
727
Art
artfenerty
Aug 30, 2003 9:50 pm
Hi All: Veriosn 1.001 is online as the development version. R1.0 is still available and will be until 1.001 passes all tests. Nothin new in Lathe, but a few...
729
John Prentice
JAPrentice@...
Aug 30, 2003 11:37 pm
Hi Well I think I understand some of the issues after about an hour of testing - however it's much more fun testing when chip and suds are flying ;=) Yahoo...
730
Steve Blackmore
stevepilotltd
Aug 31, 2003 12:42 am
... HUhh?? Does that mean there is nothing new in lathe, or there are a few bug fixes? What happened to buggy spindle or is it still there? -- Steve Blackmore...
732
joshsxr
Aug 31, 2003 2:03 am
Hello Pause is being used as a motion stop in program run mode. Yet it is not a motion stop because it is not active in MDI. Could this be changed? Thanks ...
733
Garry & Maxine Foster
gmfoster2000
Aug 31, 2003 4:34 am
Servo The link you posted to the board sure seemed to say the card has onboard video.. I was wondering the same thing Jeff was. Garry To:...
734
Art
artfenerty
Aug 31, 2003 6:32 am
Steve: I did find the problem with dwell, it could really screw things up in threading due to the shift in encoder counts being calculated during the spin-up...
735
Art
artfenerty
Aug 31, 2003 6:41 am
Steve: Sorry, no. That means almost nothing has ben done to Lathe since last version. Sorry, but too much developed this week in mill to get time for lathe. I...
736
Servo Wizard
servowizard
Aug 31, 2003 7:45 am
Garry, The auction has closed so I cannot return to see what Jeff and yourself are referring to. Having purchased four of the mainboards I can tell you for...
737
Art
artfenerty
Aug 31, 2003 7:47 am
Josh: Sorry, No. The Pause on the screen is a trajectory calculator pause, not an interpreter one. This is used because it has ramp down capability. In MDI, ...
738
Isak Levinson
isakl@...
Aug 31, 2003 8:23 am
Hi, Art. Are there any new about the backlash correction problem ? Thanks, Isak. ... From: "Isak Levinson" <isakl@...> To:...
740
japrenticeuk
Aug 31, 2003 4:45 pm
... available ... very stable now. Sorry - it's not for me. Sometimes it does not repeat, sometimes it repeats but does not decrement the Inhibit-Z value,...
741
Art
artfenerty
Aug 31, 2003 8:57 pm
Isak: Still checking, but I cannot repeat it. When I set backlash on and command a circle, for example, it rotates to the 90 degree points, ramps down, ...
742
mach1mach2cnc@yahoogr...
Aug 31, 2003 10:26 pm
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the mach1mach2cnc group. File :...
743
Servo Wizard
servowizard
Aug 31, 2003 11:50 pm
Hi, I have uploaded a file that list the definitions for Electronics Acronyms, the file will be removed in approximately one week. Servo...
744
mach1mach2cnc@yahoogr...
Sep 1, 2003 12:10 am
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the mach1mach2cnc group. File : /18sq one...
745
fcccustom
Sep 1, 2003 12:44 am
John, No I can't, but the file 18sq one up_r2_speed changes.zip I just uploaded works perfectly. !IF! I use these settings: Lower Z inhibit by .5, Z inhibit...
746
Art
artfenerty
Sep 1, 2003 4:11 am
John: Strange, mine repeats the program fine. Does the grenn light beside the repeat box go on when you enter a repeat value? This indicates the program knows...
