I set up my HF 7X10 lathe to use for milling, A flycutter seemed like the right tool for my project, MY question is how do I sharpen my HSS tools for a facing...
... A fly cutter makes an intermittent cut, so it should be ground more like a shaper bit than a lathe tool. Typically, that means more support for the edge...
... I agree with Bob. I've been using Eudora for years. Clean and fast, and has good filters.Not too hard to learn and easy to make it look the way you want it...
Hi FWIW, you can get Eudora to do very effective filtering. It takes a little time to figure out much of what and how you want to filter your emails. Try this...
Try direcway.com they are satellite Internet thru direct TV. I'm on the beach and it works anywhere, you really don't even have to have a phone. And super fast...
Look in the Steady&FollowerRests folder in the files section of this group as there are several methods illustrated there that can be adopted for your machine....
Hi folks, I have a question (imagine that ;-) If I want to take a 1" diameter rod and have it taper down to ¾" over the span of 1", just how would I do this....
You should be able to do that job with just the lathe compound slide, that is what it for, turning short tapers. -- JWE Long Beach, CA Neither the wisest...
You don't need any accessories to do this. Since it is a short taper you can do it with the tool post. One way is to make sure the chuck allen screw is in...
From what I have read, you use a center in the tailstock that is set over to one side a little bit. I have a boring head and a MT2 arbor to fit in my tailstock...
To do that Lenord you will have to have center drill, the face plate and a lathe dog. Most of the 9X20 come with the MT3 for the head stock and a MT2 for the...
Gene, The boring head, that I got for the mill, is able to be adapted to an MT2 arbor. When that adapter arrives from Enco, I had hoped to put the boring head...
Lenord, The chuck will hold your bar or work piece straight with the lathe are try to. When you off set the tail stock you will bend the bar that much. Think ...
Hi folks, I have a question (imagine that ;-) If I want to take a 1" diameter rod and have it taper down to ¾" over the span of 1", just how would I do this. ...
... For a taper this short, I'd do a little trigonometry, obtain a half angle, and set the angle on the compound. All you'll need are an accurate engineer's...
In a message dated 10/25/2003 8:07:49 PM Pacific Standard Time, ... Just remember to start cutting at the small end.so the cut won't be getting too deep for...
530
mlathemods@yahoogroup...
Oct 30, 2003 4:46 pm
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the mlathemods group. File :...
J.W., Thanks for posting this !! Looks like a good read :o) Lenord ... From: <mlathemods@yahoogroups.com> To: <mlathemods@yahoogroups.com> Sent: Thursday,...
532
mlathemods@yahoogroup...
Oct 31, 2003 2:20 pm
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the mlathemods group. File :...
Hello Folks Recently while surfing I saw A minilathe carriage gib mod. where the gib plates & gibs were tapered length wise' & could be adjusted with screws in...
Rick posted the engineering drawings for this somewhere, although I can't find them at the moment. I did this mod on my lathe and it was the single largest...
Here you go: http://warhammer.mcc.virginia.edu/ty/7x10/vault/Members/RickKruger/Tailstock/SetOver/index.html cheers, c catfish7251 <cleon@...> wrote: I...
They are at: <http://photos.groups.yahoo.com/group/mlathemods/lst> In the CamLoc2 folder. all the pictures of fitting the CamLoc and setover adjustment are...
Hi, I have recently aquired a second hand Emcomat 7, at some point in it's history the push button switch module has been removed, and replaced with a singl...
541
mlathemods@yahoogroup...
Nov 24, 2003 2:16 pm
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the mlathemods group. File :...
