Keith: If you're located in the US, here's a few names for parts that might be able to help you. Finding original-item page parts for a Wurlitzer 2000 juke is...
1221
wurlitzer@yahoogroups...
Mar 1, 2010 3:59 pm
Hello fellow jukebox fan! Please check out the Yahoo Wurlitzer Jukebox group soon, as there is always something interesting going on!...
Thank you Jim! I'll check with the people you listed. I've tried Butterfield but no others. It will be nice if I could get at least a couple complete....
... Hi Jim, Just wanted to know if you had the chance to send those directions for installing the new ballasts. Thanks again for your help. Best Regards, Shawn...
Hi Shawn! Just thought I'd jump in here, about the ballasts - I replaced all 4 ballasts on my 1400, I used 4 individual ballasts. These are about the size of...
Hi Jukebox Jimmy! It was love at first site when I first saw the Wurlitzer 1650 & I found mine on Cregslist for 550.00 & everything on it still worked. I had...
Hello from Australia. I am getting back to your advice on Wurlitzer 1250 not making some selections.Thank you to all. The problem(s) were just as described in...
Hello to all I am in need of some info on Cobra Cartridges, my question is there a way to determine whether the cartridge is good or not. Say a ohmatic value...
... If the coil shows resistance then the coil is good. Problems with the Cobra Cartridge are usually bad stylus tip or the silicon glue holding the stylus to...
Hiya Greg – Resistance of Cobra cartridge - I measured one of my 2-mil Cobras, it reads a bit under 2 ohms. About measuring resistance - you may already...
Thanks Jim Your info and time is greatly appreciated, I had three Cobra's to work with. 1.The orginial that was in it when I bought the box and it measured...
... Certainly a hum is perhaps a bad ground, however it is not coming from the Cobra cartridge. If it is only partially connected then you simply get no sound....
I bought a couple of Cobra cartridges that didnt work either> When I looked at them close it appears thet the needles/coils were held too rigid and to one...
Most cobra stylii's mounting shank are held rigidly in place by the damping/glue material. Remember that these were engineered back in the days of mono...
Hi, I just joined. I have been an AMi guy for, sheesh, 20 yrs now I guess. My first juke is the only one I still have, a 61 Continental (nice original, it's a...
Hi, Â Â Â Â I just received a 1971 wurlitzer "zodiac" jukebox. It is in very nice condition considering it's age. The unit is stuck repeating itself by...
You need to look below the deck of the record changer at the pin bank chassis. There is a crank arm that rotates above it. The crank arm contains cancel...
Here is what the guy wrote me about it: "Actually lots of stuff is running. The magazine turns, records are lifted and placed on the table. They are lifted...
Dan: I could give you more thorough answer to your problem if you could betterr describe the trouble symptoms. The Wurlamatic model record changers commonly...
Thanks for the reply. I just had a chance to go look at it and pick up the service manual he has purchased for it. Sidenote; the owner is blind, yet has taken...
Dan: On the W3700 control chassis there are 2 momentary slide switches. The free play switch will typically establish a 25 cent credit with one push,...
Jim, Â Â Â Â I found that the pins were getting stuck. I am going to take the pin bank apart and clean thoroughly. Thank you for the response. Thank you, ...
One of the micro switches is probably sticking. Lightly tap it & relays on
control center. Good luck Joe ... From: Christopher Trinkley Date: 04/02/10 18:52:46...
Yea, victory glass should have the belt. Does the carousel turn backwards if
you try to by hand? If it does the carousel is not locked down. ... From: gillywi ...
These mechs are the carousel type. Problems are usually in the small mirco
switches & relays. Tap them lightly & reseat the relays There is a lub hole
in the...
Thanks for all the replies. I am still confused about 2 things on this site: What is the proper way to reply to the answers? So far all I can figure out is to...
Hello Dan: The pinbank is directly below the record carousel,below the deck. The entire record changer can be slid forward on it's framework & tilted upward...
Chris: The pinbank on the Wurlamatic record changers tends to act like a shopping basket and collect lots of dirt/dust over time. If a thorough cleaning is...
